Smith & Wesson M&P15 Pistol AR-15 7.5-inch Barrel 5.56 NATO Blue/Black Pistol

A: Yes you are correct you can't shoot .556 through a .223, but you can shoot .223 through a .556. And the SW MP15 line of rifles/pistols *including this model) are all stamped. 556. You can shoot either .556 or .223 with this pistol, and its no worry on the question we all had learn at some point.

A: Rusty, yes Sir it is a Flat One Stage Mil-Spec Trigger with a Forged, Integral Trigger Guard & Chromed firing pin..

A: It is most likely but I've just read through 3 different reviews, looked over the specs on SW's website and watched a video review on YouTube. It doesn't say anywhere, I can guess like James to and say "yes, yes it is" but it'd just be a guess

A: I think it is however you should contact S&W to be sure By Telephone: (USA) 1-800-331-0852 Mon-Fri 8:00AM-5:00PM Eastern Time

A: Clark, yes, Overall Length: 23.5 inches (59.7 cm) Collapsed and 26.0 inches (66.0 cm) Extended. Cheers and stay safe!

A: This IS legal in MI, as the OAL is not over 26" It is 26" fully extended, and 23½" collapsed. https://www.budsgunshop.com/feeds/state_reg/michigan_restrictions.pdf

A: Clark, yes it is MI legal as overall length is not greater than 26". https://www.budsgunshop.com/feeds/state_reg/michigan_restrictions.pdf

A: yes it is legal in MI https://www.budsgunshop.com/feeds/state_reg/michigan_restrictions.pdf

A: No this is a pistol as the barrel is shorter then 16" all MD pistols must be on the MD approved handgun roster l, this one is not on the roster. https://licensingportal.mdsp.maryland.gov/MSPBridgeClient/#/home ----------------- Full details on MD restrictions here. https://www.budsgunshop.com/feeds/state_reg/maryland_restrictions.pdf

A: Bryan, no it is not on the MD handgun roster. https://licensingportal.mdsp.maryland.gov/MSPBridgeClient/#/home

A: sorry it is not on the MD approved handgun list https://licensingportal.mdsp.maryland.gov/MSPBridgeClient/#/home the enter Smith & Wesson

A: Bryan, unfortunately no, as it is not on the Maryland DOJ approved Handgun Roster : https://licensingportal.mdsp.maryland.gov/MSPBridgeClient/#/home ----- Cheers and stay safe!

A: Bryan, unfortunately no, as it is not on the Maryland DOJ approved Handgun Roster : https://licensingportal.mdsp.maryland.gov/MSPBridgeClient/#/home ----- Cheers and stay safe!

A: No sir. Good luck

A: sorry its not legal in Illinois see ******Prohibited: A semi-automatic pistol that has a detachable magazine AND one or more of the following: ✘ Any feature capable of functioning as a protruding grip that can be held by the non-trigger hand. A folding, x telescoping or thumbhole stock. ***** Barrel shroud. ✘ Muzzle brake / muzzle compensator. ***** Capacity to accept a detachable magazine outside the pistol grip. https://www.budsgunshop.com/feeds/state_reg/illinois_restrictions.pdf

A: No not legal in IL. The magazine outside the grip, and the telescoping brace, are banned features for semi auto pistols.

A: Brian, not even close to being Ill complaint. This has 3 of the 5 'evil' features. Prohibited: A semi-automatic pistol that has the capacity to accept a detachable magazine and has one or more of the following:●Any feature capable of functioning as a protruding grip that can be held by the non-trigger hand;● A folding, telescoping, or thumbhole stock;●A shroud attached to the barrel, or that partially or completely encircles the barrel,allowing the bearer to hold the firearm with the non-trigger hand without being burned,but excluding a slide that encloses the barrel;●A muzzle brake or muzzle compensator;●The capacity to accept a detachable magazine at some location outside of the pistolgrip. https://www.budsgunshop.com/feeds/state_reg/illinois_restrictions.pdf

A: Brian, no Sir, unfortunately this Handgun/Pistol has just about all the dreaded IL restricted features. Details under Handguns here : https://www.budsgunshop.com/feeds/state_reg/illinois_restrictions.pdf

A: Yes, this has a threaded barrel with 1/2×28 threads. The blast diverter muzzle brake can easily be removed/unscrewed and replaced with a suppressor. Hope this helps.

A: Yes it will work just fine with a suppressor it has 1/2×28 threads