GForce Arms GF3PD 12 Gauge Black Pump Shotgun

A: Hi John, yes sir, this has a fixed modified choke, so it will handle slugs with no issues. Be sure to use rifled (foster) slugs. You can use both 2.75" and 3" shells. https://www.budsgunshop.com/search.php/type/ammo/caliber/10000533-12+gauge/bullet_type/10001860 , Stay safe & have a great day!

A: Hi John and welcome. Yes, Foster Type Rifled Slugs are recommended for best smoothbore performance. Recommended: https://www.budsgunshop.com/product_info.php/products_id/15601/federal+vital+shok+12+ga.+2+3+4+1+oz+lead+rifle+slug+5rd+box -------------------------------------------- https://www.budsgunshop.com/product_info.php/products_id/65641/federal+power+shok+12+ga+2+3+4+1oz+lead+rifled+slug+5rd+box -------------------- Cheers, stay safe and enjoy!

A: Hi Joel, yes sir, this will feed fire both 3" and 2 3/4" shells. Stay safe & have a great day!

A: Hi Joel and welcome. This model has a 3-inch Chamber and will shoot 3-inch and 2.75-inch shells no issue. Same concept as a .357 Magnum being able to fire the shorter .38 Special. cheers, stay safe and enjoy!

A: It's chambered for 3" shells so it can load in and shoot both 2-3/4" & 3" shell cartridges.

A: it will work with both 2 3/4 and 3 inch shells

A: Hi Joel and welcome. I would check out the GeForce Arms accessories page ar: https://gfarmory.com/product-category/accessories/ ------------ Cheers and stay safe! It uses MLOK slots so you could add lights/lasers etc by using MLOK Picatinny Rail Sections - budsgunshop.com/search.php/q/picatinny+rail+section

A: Aftermarket support for this model with regards to parts to modify is almost nonexistent.

A: Hi Joel, there is not a lot out there for this no-frills GF3PD pump-action shotgun. The design is similar to the Remington 870, but there are some slight differences that prevent total parts or accessory interchangeability. The receiver is not drilled & tapped, so optics cannot be added. For a heat shield, you would need a generic shield that would most likely need to be fitted to the gun. You can also find a generic side saddle, but would need to drill for it, or you could get a shell holder that slides over the stock. There is a mag tube extension available >>> https://gfarmory.com/shop/magazine-tube-extension-with-barrel-tube-clamp/ As a side note, GF3PD is equipped with a fixed modified choke that offers some additional constriction that enables shot and 00 buck pellets to produce a tighter pattern at longer ranges. It is not recommended to run slugs through this barrel configuration.

A: Hi Joel and welcome. I would check out the GeForce Arms accessories page ar: https://gfarmory.com/product-category/accessories/ ------------ Cheers and stay safe! It uses MLOK slots so you could add lights/lasers etc by using MLOK Picatinny Rail Sections - https://www.budsgunshop.com/search.php/q/picatinny+rail+section

A: Aftermarket support for this model with regards to parts to modify is almost nonexistent.

A: Hi Joel, there is not a lot out there for this no-frills GF3PD pump-action shotgun. The design is similar to the Remington 870, but there are some slight differences that prevent total parts or accessory interchangeability. The receiver is not drilled & tapped, so optics cannot be added. For a heat shield, you would need a generic shield that would most likely need to be fitted to the gun. You can also find a generic side saddle, but would need to drill for it, or you could get a shell holder that slides over the stock. There is a mag tube extension available >>> https://gfarmory.com/shop/magazine-tube-extension-with-barrel-tube-clamp/ As a side note, GF3PD is equipped with a fixed modified choke that offers some additional constriction that enables shot and 00 buck pellets to produce a tighter pattern at longer ranges. It is not recommended to run slugs through this barrel configuration.